Skip to main content

Filter By:

Workstands

Park Tool Replacement Clamp Covers
$9.14 - $25.08
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool Repair Kit for 100-3C and 100-5C Clamps
$24.74
Park Tool's Repair Kit features the most common replacement parts for the 100-3C and 100-5C clamps. Includes: • 118s adjusting barrel • 117s eyebolt • 121s adjusting barrel pivot • 136 nut • 116s cap screws (2) • 108s-2 pins (2) • 107s-2 pin (1) • Washers (3) • E-clips (3)
Topeak FlashStand
$44.95
Topeak's FlashStand is a super work/display stand that folds up to become extremely portable as well! This affordable two-footed wonder supports your bike at the bottom bracket and down tube and raises the rear wheel with two adjustable-height feet. Take it along in the trunk of your car to dial-in your ride before your next adventure!
Park Tool Mounting Post
$184.99
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
Park Tool Adjustable Linkage Clamp
$211.06
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-3C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing. - Fits all generations of PRS-2, PRS-3, and PRS-4 stands, and PRS-5 stands manufactured before 6/96 - Fits bike frame tubes from 1" to 1-5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
Park Tool Deluxe Home Mechanic Repair Stand w/105-C Clamp
$335.95
Park Tool's Deluxe Home Mechanic Repair Stand is a heavy-duty folding stand with your choice of shop quality clamps. Perfect for heavier duty home use or portable shop use, the PCS-4 features a rock-solid, four-point leg system that folds together for storage, steel powder-coated tubing, and a composite horizontal tube. • PCS-4-1 uses the 100-5C Adjustable Linkage Clamp. • Clamp rotates 360º and is adjustable in height up to 67” (170cm) • Adjusts quickly from 55" to 72" • Approximate weight 26 lbs (11.8 kg) NOTE: The maximum weight holding capacity of the PCS-4 is 45 kg (100 lb.). However, this assumes the weight is centered over the legs.
Page 1 of 1